3 Roller Bending Machine: Specs, Roll Tooling & Buying Guide (2026)

2026-11-20
Preda
3

Every round duct that leaves a fabrication shop started life as a flat blank. Somebody had to turn that blank into a shell — and in a duct shop that somebody is usually a 3 roller bending machine. The machine class is deceptively simple: two driven bottom rolls, one adjustable top roll, and friction doing the feeding. Yet the difference between a shop that rolls true shells all day and one that fights cones, taper and marking comes down to a handful of setup disciplines that rarely appear in a sales brochure. This guide covers the working geometry of the asymmetric 3-roller, the model range a duct shop actually buys (2×1000 through 1.2×1530, plus the 2 m export class), the roll tooling that decides surface quality, how to manage the flat ends the geometry leaves behind, and what to verify at the factory before the acceptance report is signed.

Asymmetric 3 roller bending machine rolling galvanized sheet into round duct pipe, with an operator feeding the sheet and a finished round pipe section beside the machine

How a 3 Roller Bending Machine Works

A 3 roller bending machine forms sheet by pinching it between an upper roll and two lower rolls and driving the stack by friction. The two lower rolls rotate in the same direction; the sheet entering the pinch is drawn through and wrapped around the upper roll as the top roll is lowered. The finished radius is set by exactly two variables: the vertical position of the upper roll and the gap between the lower rolls. Change either and the radius changes — which is why every disciplined shop keeps a setting card per radius-and-gauge pair rather than working by feel.

Asymmetric geometry and the drop end

Nearly every light-gauge duct-class roller is asymmetric: the two lower rolls sit at different heights, with the left roll set lower than the right. The higher right roll does the forming work while the lower left roll releases the shell, so a cylinder comes off the machine without being stretched over a roll. On machines with a drop-end (tilting) upper roll, the right-hand bearing block unclamps and the top roll swings out of the way, letting a closed cylinder or a short conical section be lifted straight off instead of being slid down the shaft. For duct shells under about 1.5 mm that drop end is a convenience; for conical fittings and short cylinders it is the difference between one operator and two.

Pyramid arrangement and minimum diameter

On a pyramid machine the upper roll sits centrally between the two lower rolls and can be set low enough to roll small diameters. On a machine where the upper roll is offset to one side, the achievable minimum shell diameter grows because the sheet has to bend further to reach the roll. Either way the practical floor is set by the top roll diameter itself: you cannot wrap sheet tighter than the roll it is wrapped around. The duct-class rolls discussed below (Ø72 mm upper, Ø80 mm side) bottom out at roughly Ø100 mm shells, which covers branch ducts and short connectors but not the tight elbows that still belong on a gore locker or a segmented elbow line.

Model Range: What a Duct Shop Actually Buys

The factory range for this machine class is organised by the thickness × width envelope rather than by model name. The three standard duct-shop sizes share the same roll diameters, the same 1.5 kW drive and the same minimum shell diameter; they differ in how wide a blank they accept and how much frame sits behind it.

ModelMax thicknessMax widthUpper roll ØSide roll ØMin shell ØMotorReducerFootprint (L×W×H)
2×10002 mm1000 mm72 mm80 mm100 mm1.5 kW2201500×550×1170 mm
1.5×13001.5 mm1300 mm72 mm80 mm100 mm1.5 kW2251800×550×1170 mm
1.2×15301.2 mm1530 mm72 mm80 mm100 mm1.5 kW2702050×550×1170 mm
Export class (2 m)2 mm2000 mmbuild dependentbuild dependentbuild dependent1.5 kW classbuild dependentconfirm at quotation

Read the table as an envelope, not a menu. The 2 mm rating on the 2×1000 is a full-width rating: at 2 mm you are at the machine's limit, and the same frame running 0.8 mm galvanized has margin to spare. The wider export class (2000 mm, up to 2 mm, PLC touchscreen, CE, two-year warranty in the reference build) buys width and programmability, not a thicker envelope — the 1.2×1530 at 1.2 mm is the same physics in a smaller frame. Roller diameter, reducer ratio, frame section and weight vary between builds; confirm all four on the quotation rather than assuming the factory page numbers carry over.

Close-up of interchangeable flat steel rollers and round pipe rollers on a multi-profile sheet metal rolling machine for duct and profile forming

Roll Tooling: The Wear Part That Decides Quality

The rolls are the machine. Every defect that matters on a rolled shell — taper, lengthwise marking, a radius that wanders along the piece — traces back to roll condition or roll setting, not to the frame. Three properties decide whether a roll set will hold up in a duct shop:

  • Material and hardness. Forged carbon steel, normalised then induction or flame hardened on the working surface, is the standard for light-gauge duct rolls. The hardened case resists the embedding of swarf and scale that would otherwise print into every subsequent shell. Ask for the surface hardness figure on the quotation and check it against the manual at acceptance.
  • Bearing support. Each roll runs on two bearing blocks with grease channels accessible from outside the frame. Sealed-for-life bearings sound attractive until one fails at year three and the shaft has to come out of the frame. Regreasable blocks are the better long-term choice, and they are what the reference builds ship with.
  • Surface finish. Rolls are ground, not turned, on the working diameter. A turned roll leaves circumferential witness marks that telegraph onto polished stainless and coated galvanized sheet. Run a fingernail across the roll at the factory — you should not feel a circumferential ridge.

Roll care is cheaper than roll replacement. Clean with a brass brush only; a steel wire brush cuts micro-grooves that mark every piece afterwards. Degrease before running oily coil stock, because oil lets the sheet slip in the pinch and produces the classic "radius varies along the piece" complaint. Inspect the rolls under a bright light monthly — a ding you can see is a ding that has already marked a week of production.

The Flat End: Physics, Not a Defect

A 3 roller leaves a flat section at each end of the sheet, roughly equal to half the distance between the lower rolls. It is not a fault, a setup error or a sign of a cheap machine — the sheet simply cannot be bent until it reaches the pinch. Managing the flat is a design decision, and there are only four honest options:

  • Trim it. Add the flat allowance to the developed length and cut it off. On 0.8 mm galvanized the trim loss is small and the operation is one shear cut.
  • Design around it. Where the flat lands in a non-critical zone — behind a flange, inside a joint — leave it and let the assembly absorb it.
  • Pre-bend it. Run the two ends over a press brake or a finger brake before rolling. This is the standard answer when the flat falls on a weld or lock seam edge.
  • Move to a 4-roller. A four-roll machine pre-bends the edge in the same setup and removes the flat entirely. When pre-bending becomes a second operation on most jobs, the 4-roller plate rolling machine earns its premium.

Shops that fight the flat instead of planning for it are the ones that conclude "the machine cannot hold radius". It can. The flat was always there.

Where the shop feeds coil rather than cut blanks, the blank that reaches the roller is only as good as the equipment upstream of it. A manual or motorized decoiler pays for itself in flat, square blanks — a coil that unrolls under tension control produces none of the bow and camber that turn a good roller setup into a tapered shell.

Manual and electric coil decoiler with reel disc and handwheel for loading steel coil upstream of sheet rolling and duct forming lines

Setting Up for Repeatable Shells

Rolling faults are almost always setting, feed angle or roll condition. Standardise the sequence and the same machine that produced scrap in the morning produces a stack of identical shells in the afternoon:

  1. Check the blank is square — measure both diagonals. An out-of-square blank produces a cone no machine can correct.
  2. Set the lower roll gap for the gauge, then set the upper roll height for the target radius. Record both on the setting card and fix the card to the machine.
  3. Roll a test piece first. Measure the radius with a template, not by eye, and adjust in small steps. You can always tighten a roll; you cannot un-bend a sheet.
  4. Feed square to the rolls using the side guide, and check the first piece at both ends before running the batch. A sheet fed at an angle rolls tighter at one end — the classic cone.
  5. Support long blanks at the infeed. Unsupported sheet drops as it enters the pinch and the radius varies along the length.
  6. Never feed by hand past the pinch. Use the drive; a hand-fed sheet that slips produces a flat spot mid-shell.

Common Faults: Symptom, Cause, Fix

SymptomMost likely causeWhat to do
Cone instead of a cylinderSheet fed at an angle to the rollsUse the side guide, re-square the feed, check the first piece at both ends before continuing the batch
Radius varies along the pieceRoll gap drifted, or sheet unsupported at infeedSupport the blank, re-set the gap, verify with a template, re-check after the first few pieces
Surface marking on the sheetRoll damage, embedded swarf or oily stockClean rolls with a brass brush, degrease stock, inspect rolls under bright light; never use steel wool
Sheet slips and will not feedGap too loose for the gauge, or contaminated rollsTighten the gap to the recorded value for that gauge and degrease the rolls; use the drive, not hand feed
Machine labours on heavy gaugeMaterial at or above the thickness × width envelopeVerify against the capacity chart in the manual; reduce width or thickness rather than forcing it
Shell cannot be removed after rollingClosed cylinder on a fixed-shaft machineSpecify a drop-end upper roll; slide the shell off only after the end is released

Factory Acceptance Checklist

Run these checks at the factory, on the actual machine, before the acceptance report is signed. Every item on this list has been the root cause of a field complaint somewhere:

  • Idle-run the machine for 15 minutes: no abnormal bearing noise, no frame vibration, no oil leaks at the reducer or bearing blocks.
  • Measure both roll diameters with a micrometer and compare with the manual — not just the nameplate.
  • Check roll parallelism across the full width with a feeler or gauge; tapered radius across the width starts here.
  • Roll a test shell in your own thickest production gauge and measure diameter at three points along the length with a tape or template.
  • Verify the drop-end (if specified) clamps and releases smoothly, and that the bearing block seats solidly when clamped.
  • Confirm the electrical supply matches your shop: 380 V/50 Hz 3-phase is the standard build, with 220 V single-phase or 415 V options available on request — get it in writing on the order.
  • Ask for the setting card template, the manual capacity chart and the spare-parts list (bearings, seals, handwheels) as part of the documentation pack.
  • Witness the safety provisions: e-stop within reach of the feed position, and guarding over the pinch point that does not block blank loading.

FAQ

Can a 3 roller bend machine replace a press brake in a duct shop?

No — they make different shapes. The roller produces curves and cylinders; the press brake produces straight folds in brackets, angles and flanges. A duct shop that rolls shells still needs a brake for the pre-bend, the flanges and the fittings. The two machines feed each other.

What is the largest shell diameter I can roll?

The upper limit is set by the frame, not the rolls: anything the sheet can wrap around without hitting the machine stands. In practice, duct-class machines handle shells from about Ø100 mm up to the width of the frame. For large-diameter spiral work, a spiral tubeformer is the more productive tool.

Can I roll stainless and aluminum on the same machine?

Yes, with setup changes. Stainless work-hardens and needs a larger radius per pass to avoid cracking; aluminum marks easily, so roll cleanliness matters more. Both need their own setting cards — do not reuse the mild-steel settings.

How much does a machine like this cost?

The reference 2 m export-class build with PLC touchscreen, CE and two-year warranty lists around USD 5,800, with the smaller 1–1.5 m duct-class frames priced below that. Footprint, roll diameter, reducer and extras such as motorized top-roll adjustment move the number, so treat published figures as an order-of-magnitude guide and confirm the quotation.

Buy on the envelope you actually run — gauge, width and minimum shell diameter — and verify it with your own test blank at the factory. A correctly sized 3 roller bending machine rolls thousands of identical duct shells per year on a 1.5 kW motor and a metre and a half of floor space; the shops that get that result are the ones that wrote the settings down.

Source:Preda Machine
Write your comment right