CNC Hydraulic Shearing Machine: Blade Gap, Back Gauge & Buying Guide (2026)

2026-11-16
Preda
1

Every rectangular duct that leaves a shop starts life as a flat blank, and the quality of that blank is decided at the shear. A CNC hydraulic shearing machine cuts galvanized steel, stainless steel and aluminium sheet to length and width in a single stroke, with a programmable backgauge holding a repeatability that manual gauging cannot match. This guide covers how the machine works, which specifications matter for HVAC fabrication, how blade gap and rake angle are set, how to size the capacity class to your production, and what to verify before you sign a machine off at the factory.

Automated CNC hydraulic guillotine shearing machine cutting stainless steel and carbon steel sheet in the Preda factory, with touchscreen control panel and ball bearing work table

How a CNC Hydraulic Shearing Machine Works

A hydraulic guillotine shear — often called a swing beam shear — cuts sheet metal between two straight blades: the upper blade descends against a fixed lower blade while hold-down cylinders clamp the sheet to the table. The hydraulic system delivers constant cutting force through the stroke, and a CNC backgauge positions the cut line automatically for each length in the program. The cutting cycle is short: on the light CNC class the programmed stroke takes about 2–3 seconds, so throughput is limited by sheet handling, not by the machine.

Swing beam vs guillotine geometry

Two blade carrier designs dominate the market. A swing beam shear pivots the upper blade holder on an arc, which keeps the cutting geometry consistent through the stroke; it is the standard construction up to roughly 16 mm capacity and covers everything a duct shop cuts. A guillotine (gate type) shear moves the beam straight down, which gives more uniform blade clearance along very wide beds and is preferred on heavy beds above 4,000 mm cutting width. For duct work — where 0.5–1.5 mm galvanized steel is the daily material — either geometry produces an acceptable edge; the decision matters more when you cut stainless or thicker plate.

Rake angle and cutting force

The rake angle is the tilt of the upper blade relative to the lower blade, typically adjustable between 0.5° and 3.5° on industrial hydraulic shears. Tilting the blade shortens the instantaneous cutting length, which lowers the force required and protects the frame and drive, but it also introduces a pull-in tendency that can bow narrow strips. The Preda hydraulic guillotine range realizes the rake with a 0.5°–3.5° tilt of the upper blade holder; on the light CNC class the rake is hydraulically variable. Balance within that window: more rake for thick plate, less rake for long narrow strips where straightness matters.

Specifications That Actually Matter for a Duct Shop

Shears are sold as nominal thickness × cutting length, but two numbers decide fit: the thickness you will really cut, and the cutting width your line consumes. The table below compares the three capacity classes quoted for HVAC and sheet metal work.

ParameterLight CNC shear (export class)Industrial CNC shear 12×3200Industrial CNC shear 16×3200
Max cutting thickness4 mm12 mm16 mm
Max cutting width2,500 mm3,200 mm3,200 mm
Rake angleHydraulically variable0.5–2.3°0.5–2.3°
Stroke rate2–3 s per programmed cut8 strokes/min7 strokes/min
BackgaugeCNC programmable, ±0.1 mm repeatability600 mm range, 10–900 mm retract600 mm range, 10–900 mm retract
Main power5.5 kW15 kW15 kW
Machine weightConfirm in quotationapprox. 9.8 tapprox. 11 t
Footprint (L×W×H)Confirm in quotation3895×1800×2240 mm3915×1880×2445 mm
Indicative price levelUSD 8,500 classQuotation itemQuotation item

Two cautions when comparing quotes. First, published capacity is a thickness × width envelope: a 12×3200 machine will not cut 12 mm across the full 3,200 mm width in every material, and stainless reduces the practical envelope by roughly 20–30% against mild steel. Second, stroke-rate figures are measured differently between factories — confirm that the quoted rate applies at your gauge, and treat anything above 4 mm as a quotation item rather than a catalog number.

Preda hydraulic shearing machine with top mounted motor and NC control cabinet set up for carbon steel and stainless steel sheet cutting

Blade Material, Blade Gap and Cut Quality

The blade is the wear part that decides edge quality. Blade steels on this machine class include 6Cr2Si, 9CrSi, GCr15 and Cr12MoV, hardened to roughly HRC 56–60. Whatever the steel, the edge must come off the machine square and burr-free: a burred or rolled edge is the single most common root cause of Pittsburgh lock and drive slip seam faults downstream.

Setting blade gap

Blade gap — the clearance between upper and lower blades at the shear point — governs edge condition. Too wide and the material tears, leaving a heavy burr; too tight and the edge rolls while the machine strains. As a class rule, clearance runs roughly 5–15% of material thickness for mild steel; on the 0.8–1.2 mm galvanized used for TDF duct that is a fraction of a millimetre, set per the manufacturer's clearance card and verified on the first blank of every batch. The light CNC class offers automatic blade gap adjustment; on industrial shears it is a manual shim setting, so ask for the clearance table with the machine.

Sharpening and blade life

Blade wear is gradual and predictable: schedule sharpening by cut count, not by quality complaints. A dull blade roughly doubles cutting force, increases burr and can bow the beam. Industrial blades are typically four-edged and can be rotated and reground several times before replacement — budget grinding into the running cost, and confirm the factory ships spares or supplies them at cost.

CNC Backgauge vs Manual Backgauge

The backgauge is what justifies the premium of a CNC shear over a mechanical one. A CNC programmable backgauge with ball-screw transmission and ±0.1 mm repeatability lets the operator store a program per part number, so a batch of identical duct panels comes off with identical lengths and the first-off measurement stays valid across the batch. On a manual gauge, every length depends on operator setup and re-measuring. For shops feeding a duct line, the CNC backgauge typically pays for itself in reduced re-cuts and material waste within the first year; for a shop that cuts the same three lengths all day, a manual-gauge mechanical shear remains a rational, cheaper choice.

QC12K-12x8000 fully automatic CNC swing beam shearing machine built for high volume production, showing the feed, position and cut cycle for carbon steel processing

Sizing the Machine to Your Production

Match capacity to your worst-case material, not your average. If the daily diet is 0.5–1.2 mm galvanized with the occasional 1.5 mm stainless offcut, a 4 mm × 2,500 mm CNC shear covers the job with a wide margin and fits a standard shop bay. If you fabricate fittings from 3–6 mm plate, or feed a heavy spiral tubeformer with slit strip, step up to the industrial class — the 12×3200 at 15 kW and about 9.8 t is the usual entry point. A throughput check: at 2–3 seconds per programmed cut the light CNC shear returns roughly 1,200–1,800 cuts per hour, several times what a treadle shear can sustain; the industrial class at 7–10 strokes/min is limited by handling, not the machine. Confirm the electrical supply early: the industrial class draws 15 kW and above, and Preda configures voltage (220/380/415/440 V) and phase (1PH/3PH) before production — state your supply with the order, not after delivery.

Factory Acceptance Checklist

  • Test-cut three blanks of your thickest material; measure both diagonals of each — equal diagonals mean a square blank.
  • Verify backgauge accuracy at three programmed positions, including full stroke, with a calibrated tape or caliper.
  • Inspect the cut edge for burr and roll; have the factory demonstrate blade gap adjustment or show the clearance card.
  • Check hold-down pressure is even across the width — uneven clamping lifts thin sheet and bows the cut.
  • Confirm the safety package: emergency stops on the machine, foot switch, and guarding as ordered.
  • Run the machine at full width for ten minutes; look for hydraulic leaks, abnormal noise and frame vibration.
  • Check documentation: CE declaration, electrical drawings, operation manual and warranty terms (the export class ships with a 2-year warranty).
  • Confirm voltage, phase, foundation and craneage requirements against the footprint and weight in the quotation.

Common Faults and Fixes

SymptomLikely causeFix
Heavy burr on the cut edgeBlade gap too wide, or blade wornReset clearance for the gauge; rotate or sharpen the blade
Blank not squareBackgauge or side guide out of squareSquare the gauge; check both diagonals on the first blank
Cut length varies through the batchBackgauge drift or sheet slipping at the hold-downVerify gauge position; increase hold-down pressure
Cut edge not straightSheet lifting during the cutApply even hold-down pressure; avoid narrow unsupported strips
Edge rolled or deformedClearance too tightOpen the gap to the table value for the gauge
Machine strains at full widthAt the thickness × width capacity limitNever exceed the rating; check the capacity chart for the material

FAQ

Can a hydraulic shear cut stainless steel?

Yes, within a reduced capacity envelope — typically 20–30% less thickness than mild steel — with blades and clearance set for the material and the rake angle adjusted to control pull-in.

What is the difference between a swing beam and a guillotine shear?

A swing beam shear pivots the upper blade on an arc; a guillotine moves it straight down. Guillotine geometry suits the widest, heaviest beds; swing beam is the standard for duct-shop capacities.

How often do blades need sharpening?

By cut count rather than calendar. Inspect weekly — a dull blade shows up as burr, higher force and bowed cuts long before it fails outright.

What width machine do I need?

2,500 mm covers standard duct panels and most line feeds; 3,200 mm is the common industrial step up; 4,000 mm and beyond only pay off if you regularly cut full-width sheets.

Where It Fits in the Preda Line

Preda builds the shear as the first station of a rectangular duct workflow: cut blanks on the shear, form Pittsburgh locks and drive slips on the lock former, bead and flange on the TDF flange former, and close corners with the corner matics — or automate the whole sequence on an auto duct line. Shops that only cut 1.5 mm panel all day can run the lighter electric shearing machine instead; complex fitting blanks that no straight shear can produce go to the CNC plasma cutting machine, which complements rather than replaces the shear.

Source:Preda Machine
Write your comment right