A CNC laser cutting machine and a CNC plasma cutting machine look like siblings: both are gantry tables driven by nesting software, both cut sheet metal from a CAD/CAM file, and both eliminate hand layout from the shop. The Preda PL series fiber laser lists from around $25,000 against roughly $5,000 for the plasma table — a five-fold gap that makes the buying decision a process question, not a brand question. The correct choice depends on what you cut, how clean the edge must be, and what the finished part feeds into next.
For a duct shop running an automatic duct line or a TDF flange former, the cutting table is the first machine in the chain: every panel and fitting passes through it. This guide compares the two processes on the parameters that decide throughput and cost — edge quality, material range, power draw and consumables — so the specification you send to vendors matches your work.
A fiber laser generates the beam in diode-pumped fiber modules, delivers it through a armored fiber cable, and focuses it through a collimator and focus lens onto a spot roughly 0.1–0.2 mm across. That concentrated energy melts the metal locally while an assist gas — nitrogen, oxygen or compressed air — blows the melt out of the kerf and, in the case of nitrogen on stainless and aluminum, shields the edge from oxidation. Because nothing touches the workpiece, there is no torch height to drift, no arc to wander and no electrode to oxidize.
The fiber laser emits at 1064 nm, a wavelength that metals absorb far more readily than the 10.6 µm beam of a CO2 laser. Aluminum, brass and copper — reflective materials that defeat older laser technologies and cut slowly or expensively with torch processes — run at production speed on fiber. For a duct shop this matters directly: kitchen exhaust in stainless, clean-room aluminum duct and architectural exposed work are exactly the jobs where the fiber laser earns its premium.
The PL series is configured rather than ordered off a single datasheet: three bed sizes cover 1500×3000, 1500×6000 and 2000×6000 mm, and laser power is customizable from 1000 W to 6000 W. The published platform covers mild steel, stainless and aluminum in one setup, with CNC control, nesting software, CE certification and a two-year warranty.
| Model | Cutting area | Laser power | Typical fit |
|---|---|---|---|
| PL-1530 | 1500×3000 mm | 1000–1500 W typical | Standard 1220×2440 mm stock; full duct panels |
| PL-1560 | 1500×6000 mm | 1000–3000 W | Long fittings, two-up nesting of panel sets |
| PL-2060 | 2000×6000 mm | 2000–6000 W | Wide sheet, heavy structural and bracket work |
Selection logic is sheet-driven. If your stock is 1220×2440 mm galvanized and your longest fitting is under 2400 mm, the PL-1530 covers everything with margin. Move to the 1560 when you want to nest two panel sets per sheet or cut long transitions without segmentation, and to the 2060 when wider sheet or thicker structural stock enters the mix. Buying bed you cannot fill is the most common overspecification error on this machine class.
Power determines how thick you can cut with good edge quality — and for duct work, the quality band sits far below the sever limit. The windows below are class-typical for industrial fiber lasers of each power rating; treat them as the conversation frame with your vendor, then demand test cuts on your own material before committing.
| Laser power | Mild steel (quality cut) | Stainless steel | Aluminum | Duct-shop relevance |
|---|---|---|---|---|
| 1000 W | ~4 mm | ~3 mm | ~2.5 mm | Covers 24–16 ga with margin |
| 1500 W | ~6 mm | ~5 mm | ~3 mm | Thin duct plus brackets and gussets |
| 2000 W | ~8 mm | ~6 mm | ~5 mm | Mixed duct and structural work |
| 3000 W | ~10–12 mm | ~8–10 mm | ~6 mm | Heavy fittings, plenum plates |
| 6000 W | ~16–25 mm | ~12–16 mm | ~10–12 mm | Beyond typical duct fabrication |
Note the asymmetry with plasma: on the thin galvanized band that dominates duct work, both processes cut easily — the difference shows up on thin stainless and aluminum, where plasma edges need grinding and laser edges go straight to forming.
Plasma leaves a heat-affected zone and, on thin material, dross along the back edge. On galvanized mild steel that is acceptable — the edge disappears into a Pittsburgh seam or a TDF flange. On thin stainless and on visible architectural duct, slag and HAZ mean hand finishing, and hand finishing is what you bought a CNC table to eliminate. A nitrogen-assisted fiber laser cuts those materials with a narrow kerf, a square edge and no oxide film, at tolerances that hold fittings within a tenth of a millimetre on a maintained machine.
Machine price is one line. The operating comparison below is what decides the payback period — figures are class-typical and should be confirmed against your local utility and gas prices.
| Cost factor | CNC plasma table | Fiber laser (PL series) |
|---|---|---|
| Machine price (from) | ~$5,000 | ~$25,000 |
| Electrical draw | ~3 kW table plus source | Laser plus chiller; tens of kW at higher powers |
| Assist gas | Compressed air (dry, filtered) | Nitrogen for bright cutting; oxygen or air for steel |
| Consumables | Electrodes, nozzles, caps — scheduled wear | Nozzles, protective windows, lenses — much lower rate |
| Edge finishing | Grinding on thin stainless/aluminum | Minimal to none |
| Material range | Any conductive metal | Metals; organics need different processes |
| Environment tolerance | Robust in dirty shop conditions | Cleaner air and stable power recommended |
Plasma remains the rational choice when the work is thick mild steel and galvanized at high duty cycle, when capital is constrained, and when the shop environment is less than pristine. The laser wins when the mix includes thin stainless, aluminum or brass; when edges are visible or feed precision fittings; when one machine must handle steel, stainless and aluminum in the same shift; and when eliminating grinding labor is worth five times the machine price. Many larger fabricators run both — plasma for the heavy panel work, laser for the fitting and specialty nest.
Plan three things before the crate arrives. First, electrical capacity: the laser source and its water chiller together draw far more than a plasma table, so have an electrician size the feed for the configuration you ordered, not the entry model. Second, the chiller needs its own footprint, water quality management and a maintenance schedule — laser downtime is usually thermal, not optical. Third, assist gas: nitrogen purity and pressure govern edge brightness on stainless and aluminum, so budget cylinders or an on-site generator with the machine. Laser cutting still requires fume extraction, and the machine must be enclosed or guarded against reflected 1064 nm energy when cutting aluminum and brass.
| Symptom | Likely cause | Fix |
|---|---|---|
| Dross on the back edge | Gas pressure low, speed too high, or focus too deep | Raise assist gas, slow down, re-focus per material chart |
| Yellow edge on stainless | Nitrogen purity or pressure insufficient | Check N2 supply and moisture; raise pressure |
| Cut stops mid-contour | Back-reflection protection triggered | Clean nozzle, check material reflectivity settings |
| Kerf wider than program | Worn or contaminated nozzle | Replace nozzle and protective window |
| Over-temperature alarm | Chiller fault or dirty filters | Service chiller, clean heat exchangers |
| Parts out of tolerance at bed ends | Machine level or calibration drift | Re-level, run bed compensation, recalibrate |
If your work is galvanized mild steel only, plasma is the economical answer. If stainless, aluminum or visible work is more than a minor share of your nest, the laser pays for itself in eliminated grinding and tighter fittings.
Match the bed to your sheet stock and longest part. 1220×2440 mm stock and sub-2.4 m fittings fit the PL-1530; long transitions or two-up nesting justify the PL-1560.
For 0.5–1.6 mm duct gauges, 1000–1500 W is sufficient. Step up only for thicker structural stock — buying power you cannot use costs money twice, at purchase and in electricity.
For metals, yes — and better on thin reflective stock. Plasma still leads on thick mild steel at low capital cost.
On a maintained machine, expect positioning in the hundredths of a millimetre and cut-part accuracy in the tenths. Confirm with the taper and stacking tests above.