An electric shearing machine — the powered guillotine shear that sits beside the folding and seaming machines in every duct shop — cuts galvanized panels, blanks and cleat strips to size without the arm-power limits of a treadle shear. Two capacity classes dominate the market: the Q11S workshop series rated 2–4 mm, and the light 1.5 mm export series built for high-throughput panel cutting. This guide compares the two classes on the specifications that decide fit, and covers blade care, safety, power supply, acceptance checks and the faults you will actually meet on the floor.
An electric guillotine shear drives the upper blade down against a fixed lower blade with an electric motor, so every stroke is delivered at the same speed and force regardless of operator effort. The workflow has three steps: position the sheet against the backgauge, clamp it with the workholding clamp, and stroke. The Q11S workshop series runs at 33 strokes per minute with a 2°14′ shear angle; the light export series reaches about 30 strokes per minute behind a 1.5–2.2 kW motor. Both cut square, straight and repeatably — the difference between the classes is capacity, not principle.
| Parameter | Q11S workshop series | 1.5 mm export series |
|---|---|---|
| Models | Q11S-2×1000 / 2×1300 / 2×2500, 3×1000–3×2000, 4×1300 / 4×1600 | 1.5×600 / 1.5×1000 / 1.5×1300 / 1.5×1500 |
| Max cutting thickness | 2–4 mm by model | 1.5 mm |
| Max cutting length | 1,000–2,500 mm | 600–1,500 mm |
| Shear angle | 2°14′ | Fixed rake, confirm per build |
| Stroke rate | 33 strokes/min | approx. 30 strokes/min |
| Backgauge stroke | 400–500 mm | Precision backgauge positioning |
| Motor power | 3–5.5 kW | 1.5–2.2 kW |
| Footprint (L×W×H) | 1600×1000×1100 to 3300×1100×1200 mm | Compact floor or bench configuration by width |
| Safety | Emergency stop and foot switch | Light curtain guarding standard |
| Certification / warranty | CE class certification, 2-year warranty | CE certified, 2-year warranty |
| Indicative price level | Quotation item | USD 3,200 class |
Published figures come from the manufacturer's specification sheets. Stroke rate, motor power and guarding details vary by build, so treat the table as a selection framework and confirm the exact configuration in your quotation.
The choice is a capacity decision. If your daily work is 0.5–1.2 mm galvanized duct panel — the TDF and Pittsburgh lock range — the 1.5 mm export series is purpose-built: about 30 strokes a minute, a 1.5–2.2 kW motor that runs from a standard shop supply, and light curtain guarding as standard. The 1.5×1300 width covers standard duct panel blanks and the 1.5×1500 handles wider layouts, so most small and mid-size shops never need more machine than this.
Step up to the Q11S series when any of the following is true: you regularly cut 2 mm or 3 mm material, you cut stainless offcuts — stainless work-hardens and punishes light machines — you need a 2,500 mm bed to feed a duct line, or you want the heavier 3–5.5 kW drive and welded frame for all-shift running. The Q11S-3×1300 at 4.5 kW is the usual sweet spot for a busy duct shop; the Q11S-2×2500 is the line-feed machine. Do not buy a 4 mm model unless you truly cut 4 mm — you pay for frame, motor and floor space you will never use.
Blades on this machine class are supplied in 6Cr2Si and similar tool steels, hardened to roughly HRC 56–60, and are typically four-edged so they can be rotated and reground before replacement. Edge quality is governed by blade gap: as a class rule the clearance between the upper and lower blades runs roughly 5–15% of material thickness, so on 1 mm galvanized it is a fraction of a millimetre. Too wide a gap tears the sheet and leaves a burr that later shows up as a Pittsburgh lock that will not close; too tight rolls the edge and strains the drive. Set the gap per the manufacturer's clearance card for the gauge, inspect the first cut of every batch, and schedule sharpening by cut count — a dull blade doubles the effort and bows narrow strips.
The export series is deliberately easy to install: a 1.5–2.2 kW motor on a standard shop supply, with voltage options of 220 V / 380 V / 415 V / 440 V and single-phase or three-phase configuration confirmed before production. The Q11S series draws 3–5.5 kW and occupies 1,600–3,300 mm of floor length on a 1,000–1,100 mm width; allow working clearance in front of the table for sheet handling and behind for backgauge travel. Either way, confirm your supply against the nameplate before the machine ships — retrofitting voltage or phase after delivery is a service call you do not need.
Light curtain guarding is standard on the export series and stops the stroke the moment the field is breached — on a machine cycling 30 times a minute, this is the difference between a safe shop and an incident. The Q11S series ships with emergency stop and foot switch controls. On either class, position the foot switch so the operator's hands stay clear of the blade line, never run the machine with guarding removed, and expect the light curtain, e-stops and fixed guarding to be the first items a CE-oriented insurer asks about.
| Symptom | Likely cause | Fix |
|---|---|---|
| Heavy burr on the cut edge | Blade gap too wide, or blade worn | Reset clearance for the gauge; rotate or sharpen the blade |
| Blank not square | Backgauge or side guide out of square | Square the gauge; check diagonals on the first blank |
| Cut length varies | Backgauge drift or sheet slipping at the clamp | Verify gauge position; increase clamp pressure |
| Cut edge not straight | Sheet lifting during the cut | Apply even clamp pressure; avoid narrow unsupported strips |
| Motor stalls on thick stock | Material above the model's thickness rating | Check against the model limit; step up to the next capacity class |
| Edge rolled or deformed | Clearance too tight | Open the gap to the table value for the gauge |
600, 1,000, 1,300 and 1,500 mm on the 1.5 mm export series; 1,000 to 2,500 mm across the Q11S workshop series.
Up to 1.5 mm on the export series — the full HVAC duct gauge range — and 2–4 mm depending on the Q11S model.
About 30 strokes per minute on the export series and 33 per minute on the Q11S series, so panel cutting keeps pace with the rest of the shop.
The electric shear is the everyday panel cutter: lower cost, faster cycle, 1.5–4 mm capacity. The CNC hydraulic shear adds a programmable backgauge, a heavier hydraulic drive and 4–16 mm capacity for shops that need batch repeatability or thicker plate.
Light curtain guarding as standard on the export series; emergency stop and foot switch on the Q11S series, with CE certification on both classes.
Cut panels on the electric shear, then form locks and seams on the Pittsburgh lockformer, flanges on the TDF flange former, and feed the whole sequence from an auto duct line. When a shop outgrows the electric class, the step up is the CNC hydraulic guillotine shear range rated to 30 mm.